Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
- Brake system
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake lines and hoses
   Pumping of brake system
   Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Cable replacement (ов) drive of the parking brake
   Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
   Check of serviceability of functioning and replacement of the sensor switch of level of brake liquid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of the main brake cylinder

Failed GTTs is subject to replacement. Manufacturers do not recommend to undertake attempt of carrying out regenerative repair of the main brake cylinder.

REMOVAL

 PERFORMANCE ORDER

1. The main brake cylinder is in an impellent compartment of the car and is fixed on assembly of the vacuum amplifier of brakes.
2. Pump out from the GTTs tank as the bigger amount of liquid available in it (use a syringe or a rubber pear) is possible.
3. Enclose rags under shtutserny connections and prepare caps or plastic bags for a blockage of the open ends of brake lines for the purpose of hit prevention in dirt system.

Brake liquid is among aggressive chemical compounds and at contact to body panels destroys a paint and varnish covering. Before starting performance of procedure cover wings and the panel of a front of the car with special covers, or simply old blankets.

4. Weaken nuts of shtutserny knots of connection to GTTs of brake lines. In order to avoid a rounding off шлицов nuts give them by means of a special cap natural a cutting head. Having slightly delayed outside, separate brake lines from unions of the main cylinder. At once закупорьте open ends of tubes.

5. Remove a rasporny bar of racks of a forward suspension bracket.

6. Disunite the socket of electroconducting of the sensor switch of level of brake liquid on the GTTs tank case, then release two fixing nuts and separate the main cylinder from assembly of the brake amplifier. Remove the cylinder from fixing hairpins and take it from an impellent compartment (try not to spill hydraulic liquid filling the cylinder on the painted body panels).

INSTALLATION

 PERFORMANCE ORDER

1. Before installation new GTTs is necessary for pumping over on a workbench. For convenience clamp a landing flange of the cylinder in a vice with soft sponges. Further it is necessary to manipulate at the same time the piston in the cylinder and to watch a stream of the brake liquid which is pushed out through the final union.
Connect to the GTTs final unions pair of tubes from a special set for pumping (ask in shops of automobile accessories).

2. Fill in in the tank fresh brake liquid of a demanded grade (see. Head of Control and routine maintenance).
3. Slowly push pistons in the cylinder (it will be most convenient to use a big screw-driver with a crosswise sting). Air should start to leave delivery chambers in the tank. It is thus important, that the ends of both tubes were completely shipped in the brake liquid which was in the tank to exclude probability of a podsasyvaniye it back in the cylinder at an otpuskaniye of pistons.
4. Continue pumping until liquid pushed out through tubes completely will not be released from air bubbles.
5. Serially disconnect tubes, at once corking the open ends of unions. Close the GTTs tank a cover.
6. Put on GTTs hairpins on assembly of the vacuum amplifier and while only by hand, tighten fixing nuts.
7. Screw in the cylinder unions of brake lines. As the cylinder is not fixed yet finally, its situation can be corrected slightly for the purpose of simplification of procedure of a vvorachivaniye of unions - try not to strip a thread.
8. Tighten with demanded effort of a nut of fastening of GTTs, then densely tighten shtutserny connections.
9. Establish into place a rasporny bar of racks of a forward suspension bracket and tighten its fixture with demanded effort.
10. Fill in in the GTTs tank fresh brake liquid and pump over hydraulic system (see. Section Pumping of brake system). GTTs pumping on the car (if did not do it on a workbench) will need the help of the assistant which will manipulate a pedal of a foot brake. Ask the assistant to squeeze out several times a pedal, then to fix it in the bottom situation. Weaken a shtutserny nut, letting out from the cylinder an air mix with brake liquid. Repeat procedure until pushed-out liquid completely will not be released from air bubbles. Operating in a similar manner, pump over the second union.

Hold near at hand pure rags for the purpose of immediate removal of traces of brake liquid getting on painted body surfaces.

11. Before starting car operation, make sure of serviceability of functioning of brakes.