Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
- Brake system
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake lines and hoses
   Pumping of brake system
   Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Cable replacement (ов) drive of the parking brake
   Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
   Check of serviceability of functioning and replacement of the sensor switch of level of brake liquid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of supports of disk brake mechanisms

Remember that developed in the course of operation of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl alcohol!

Supports of both brake mechanisms of one axis should change at the same time.

Brake mechanisms of forward wheels

REMOVAL

 PERFORMANCE ORDER

1. Weaken wheel nuts. To Poddomkratta a car front also establish it on props. Remove wheels.
2. Disconnect from a support the hydraulic line, for the purpose of minimization of losses of brake liquid, and also, in order to avoid hit in a dirt path закупорьте shtutserny connection.

3. Turn out fixing bolts.

4. Remove a support from an anchor bracket.

INSTALLATION

 PERFORMANCE ORDER

1. Installation is made upside-down. Do not forget to replace copper sealing washers (laying) from both parties of the shtutserny socket of connection to a support of a brake hose. Usually the set of new laying is applied in a remnabor. Tighten bolts of fastening of a support and a hollow bolt of shtutserny connection with demanded effort.
2. Pump over a brake contour (see. Section Pumping of brake system). Check on existence of signs of leaks shtutserny connections of brake lines.
3. Establish to the place of a wheel, lower the car on the earth and tighten nuts of fastening of wheels with demanded effort (see. Specifications to Head of Control and routine maintenance). Before starting operation of the car check serviceability of functioning of brakes.

Brake mechanisms of back wheels

REMOVAL

 PERFORMANCE ORDER

1. Weaken wheel nuts. To Poddomkratta a car back also establish it on props. Remove back wheels.

2. Release the lever of the parking brake, take a clamp and liberate a driving cable from the arm on the back party of a support of the brake mechanism.

3. Disconnect a driving cable from the executive lever on a support.

4. Turn out a hollow bolt of shtutserny connection of a brake hose on a support. To Zakuporta of an opening by means of pair of pieces of a rubber hose.

5. Turn out bolts of fastening of a support.

6. Turn out bolts of fastening of a support

INSTALLATION

 PERFORMANCE ORDER

1. Installation is made upside-down. Do not forget to replace sealing washers (laying) from both parties of the shtutserny socket of connection to a support of a brake hose. Usually the set of new laying is applied in a remnabor. Tighten bolts of fastening of a support and a hollow bolt of shtutserny connection with demanded effort.
2. Pump over a brake contour (see. Section Pumping of brake system). Check on existence of signs of leaks shtutserny connections of brake lines.
3. Establish to the place of a wheel, lower the car on the earth and tighten nuts of fastening of wheels with demanded effort (see. Specifications to Head of Control and routine maintenance). Before starting operation of the car check serviceability of functioning of brakes.