Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
- Brake system
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake lines and hoses
   Pumping of brake system
   Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Cable replacement (ов) drive of the parking brake
   Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
   Check of serviceability of functioning and replacement of the sensor switch of level of brake liquid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Replacement of brake shoes of disk brake mechanisms

Replacement of brake shoes should be made at the same time on both forward/back brake mechanisms. Remember that developed in the course of operation of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system gasoline or solvents on an oil basis, - apply only firm cleaners or methyl alcohol!

Procedure equally belongs to disk brake mechanisms both forward, and back wheels.


 PERFORMANCE ORDER

1. Uncover the tank of brake liquid.
2. Weaken nuts of fastening of the corresponding wheels. To Poddomkratta a car front/back also establish it on props.
3. Remove forward/back wheels.

Replacement of all four blocks of brake mechanisms of both wheels of one axis should be made at the same time. In order to avoid confusion work with each mechanism in an individual order.

4. Attentively examine a brake disk (see. Section condition Check, removal and installation of a brake disk). In case of need pro-point performance, remove a disk.

Brake mechanisms of forward wheels

 PERFORMANCE ORDER

1. By means of a clamp drown the piston in the support cylinder, having provided with that necessary free space for installation of the new blocks having big thickness. At a piston utaplivaniye in a support liquid level in the GTTs tank will rise, - watch, that it did not start to overflow, in case of need pump out surplus.

2. Before starting dismantle of components surely wash them a special cleaner. Further act according to the instructions provided on illustrations below.

Brake mechanisms of back wheels

 PERFORMANCE ORDER

1. Wash out assemblies of brake mechanisms by special cleaning structure. Further act according to the instructions provided on illustrations below, then pass to performance of the procedure described below in paragraph 1.

 

2. Cover the back party of new blocks with special antivizgovy structure. The instruction on using means is usually unpacked on a ballonchik wall.

3. Establish adjusting laying on the blocks.
4. Establish holders of blocks in an anchor bracket of a support. Grease holders of blocks with a thin layer of high-temperature greasing.
5. Establish new brake shoes with adjusting laying in an anchor bracket of a support.

6. By means of nippers turn the piston, having drowned it in the support cylinder for the purpose of providing necessary free space under installation of new brake shoes.

7. At first drown the piston to the bottom the cylinder, then turn out it back so that at installation of an internal block the ledge on its back party got to one of a vyborok on a face surface of the piston. Track, that as a result of rotation of the piston it did not appear its boot is deformed.

Brake mechanisms of lobbies and back wheels

 PERFORMANCE ORDER

1. Establish to the place of a wheel, lower the car on the earth and tighten nuts of fastening of wheels with demanded effort (see. Specifications to Head of Control and routine maintenance).
2. Several times squeeze out a brake pedal / cock the lever of the parking brake (if changed back blocks) for the purpose of a usadka of blocks on a disk.
3. Check level of brake liquid, in case of need make the corresponding adjustment (see. Head of Control and routine maintenance). Before starting normal operation of the car, make sure of serviceability of functioning of brake system.