Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
- Engine management
   System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions
   Removal and installation RSM/ESM
   Check of serviceability of a condition and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a condition and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a condition and replacement of the sensor of temperature of soaked-up air (IAT)
   Check of serviceability of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats)
   Check of serviceability of a condition and replacement of the sensor of VMT/provision of a cranked shaft (TDC/CKP)
   Check of serviceability of a condition and replacement of the sensor of position of pistons (CYP)
   Check of serviceability of a condition and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a condition and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a condition and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a condition and replacement of the sensor of a detonation
   Check of serviceability of a condition and replacement of the sensor of speed of movement of the car (VSS)
   Check of serviceability of functioning and replacement of the valve of stabilization of turns of idling (IAC)
   Check of serviceability of functioning and replacement of the air valve of correction of structure of an air and fuel mix (FIA)
   System of operated ventilation of a case (PCV)
   System of a retsirkulyatsiya of the fulfilled gases (EGR) - the general information, check of a condition and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a condition and replacement of components
   The catalytic converter - the general information, check of a condition and replacement
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Check of serviceability of a condition and replacement of the detector of control of electric loadings (ELD)

CHECK

 PERFORMANCE ORDER

1. The ELD system reveals signs of an overload of electric chains of systems of external lighting and alarm devices, injection of fuel, a charge etc. The first symptom of such overloads is violation of stability of giving of a food on single turns of the engine. Failure of the detector leads to record in memory of system of self-diagnostics of a code of malfunction Р1297 or Р1298.

2. Remove ELD (see below paragraph 1) and disconnect from it electroconducting. Measure tension between the plug 1 (+) and weight on the socket from a plait at the included ignition (the engine do not start). The nominal rate equals to tension of the battery. If tension is absent, check an electroconducting condition on a site between a safety lock No. 6 on 15 And and the detector.

3. At the included ignition (do not start the engine) measure tension between the plug 3 (+) and weight on the socket from a plait. Demanded value makes 4.5 ÷ 5.0 V.Pri otsutstvii of demanded result check a condition of electroconducting of ELD on a site between the engine and the generator.
4. Make sure available conductivity between the plug No. 2 and weight.
5. In case of negative results described above checks replace the ELD block.

REPLACEMENT

 PERFORMANCE ORDER

1. The ELD block is located in the assembly block of safety locks/relay in an impellent compartment of the car. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Turn out two fixing screws, take the ELD block from the central part of the assembly block and disconnect from it electroconducting.

3. Installation is made upside-down.