Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
- Engine management
   System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions
   Removal and installation RSM/ESM
   Check of serviceability of a condition and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a condition and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a condition and replacement of the sensor of temperature of soaked-up air (IAT)
   Check of serviceability of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats)
   Check of serviceability of a condition and replacement of the sensor of VMT/provision of a cranked shaft (TDC/CKP)
   Check of serviceability of a condition and replacement of the sensor of position of pistons (CYP)
   Check of serviceability of a condition and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a condition and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a condition and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a condition and replacement of the sensor of a detonation
   Check of serviceability of a condition and replacement of the sensor of speed of movement of the car (VSS)
   Check of serviceability of functioning and replacement of the valve of stabilization of turns of idling (IAC)
   Check of serviceability of functioning and replacement of the air valve of correction of structure of an air and fuel mix (FIA)
   System of operated ventilation of a case (PCV)
   System of a retsirkulyatsiya of the fulfilled gases (EGR) - the general information, check of a condition and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a condition and replacement of components
   The catalytic converter - the general information, check of a condition and replacement
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation RSM/ESM

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.

In order to avoid RSM damage by the electrostatic category, try not to touch contact plugs of the module. Whenever possible make self-grounding. RSM is included into number of components of anticreeping system and provides an engine immobilization. At RSM replacement the new module before start of the engine is necessary for programming in the conditions of a car-care center workshop. Actually RSM replacements, strictly speaking, it will be also more correct to charge performance to experts.


 PERFORMANCE ORDER

1. The module of management of RSM is in car salon under the dashboard, near assembly of the central console.
2. Disconnect SRS (see. Head Onboard electric equipment).

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for equipment introduction in action!

3. Unscrew a carpet from the lower part of the central console in driver's and passenger foot wells (see. Head the Body), should open unhindered access to RSM assembly.

4. Disunite the RSM electric sockets.

In order to avoid processor damage ignition at shutdown/connection of electroconducting should be switched off (a key in the situation OFF).

5. Turn out bolts of fastening of a basic arm of RSM.

6. Carefully remove RSM.

In order to avoid RSM damage by a static electricity, try not to touch contact plugs of the module. Whenever possible make self-grounding. To storage of the module apply special electrostatic laying (ask in shops of automobile accessories).

7. Installation is made upside-down.

At replacement of the module it is necessary to enter into it a code of system of an immobilization of the engine in the conditions of a car-care center workshop.