Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information
   Check of functioning of system of ignition
   Check of a condition and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management with ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Replacement of a regulator of tension and generator brushes
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and starter installation
   Removal and installation of the traction relay
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Check of serviceability of functioning and replacement of the module of management with ignition (ICM)

CHECK

 PERFORMANCE ORDER

1. Check serviceability of giving of a food on the ignition module. Disconnect electroconducting from the ICM module. At the included ignition (without starting the engine) check tension existence in the following points:
a) On the V6 models connect the voltmeter between the plug of a black and yellow wire (plug No. 2) and mass of a body. The device should fix tension of the battery;

b) On 4-cylinder models it is necessary to remove a cover and a begunok from the distributor, then to disconnect from the ICM module a black and yellow wire and to check tension existence between its plug and weight at the included ignition and not started engine.

2. Check a condition of a contour of ignition and accompanying components. If tension on ICM is absent, check an electroconducting condition on a chain site between the module and the ignition switch (see. Head Onboard electric equipment). First of all always it is necessary to check a condition of safety locks of the switch of ignition of No. No. 41 (on 100 And) and 42 (on 50 And) in the assembly block of relays/safety locks located under a cowl. Also check a safety lock No. 6 (on 15 And) in the assembly block under the car dashboard. Attentively investigate an electric contour and make sure that the switch of ignition provides food giving on ICM at key turn in the situation ON. In case of need address to schemes of electric connections.
3. Make sure of serviceability of giving of a food from the ignition coil on ICM. At the included ignition (do not start the engine) make sure available tension between white-black (4-cylinder VTEC engines) / white-dark blue (4-cylinder engines without VTEC) / dark blue (V6 engines) a wire and in mass of a body. Tension of the battery should take place.
4. If tension is absent, check a chain on a site between the corresponding wire and the coil. Also check coil windings (plugs A and B on 4-cylinder engines and plugs 1 and 3 on V6 engines) on existence of internal breaks (see. Section Check of a condition and replacement of the coil of ignition).
5. If the coil and chain electroconducting as it should be, and an iskroobrazovaniye is absent, replace ICM.

REPLACEMENT

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


2. Remove from the distributor a cover and (at the corresponding complete set) the filter (see. Head of Control and routine maintenance).
3. Disunite all electric sockets on ICM.
4. Turn out from the ICM case two fixing screws and remove the module, having pulled it outside.

5. Installation is made upside-down.