Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information
   Check of functioning of system of ignition
   Check of a condition and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management with ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Replacement of a regulator of tension and generator brushes
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and starter installation
   Removal and installation of the traction relay
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Check of functioning of system of ignition

 PERFORMANCE ORDER

In view of that in system of ignition very high voltage is developed, service of its components should be made with extra care. This remark belongs not only to the main knots of electronic system of ignition, but also and to all accompanying components, including tips of candle wires, a tachometer and the other diagnostic equipment.

1. At violation of serviceability of functioning of system of ignition before starting diagnostics of a condition of the distributor, execute the following preliminary checks:

a) Check a condition of terminal connections of the battery and reliability of a tightening of clips of fastening of tips of wires on them;
b) Check a battery condition (see. The section Check of a condition and battery replacement), in case of need make its replacement;
c) Check an external condition of VV of wires of the distributor and the coil of ignition and reliability of their fastening on plugs;
d) At the corresponding complete set check a condition of fusible inserts in located in an impellent compartment of the car the assembly block (see. Head Onboard electric equipment). Fused elements replace.

2. Check serviceability of an iskroobrazovaniye on spark plugs. If the engine is turned, but not started, disconnect VV a wire from one of spark plugs and connect it to the special calibrated tester (ask in shops of automobile accessories). A clip of a tester fix on a bolt or a metal arm of the block of the engine, having reliably earthed it thereby on weight. In the absence of near at hand calibrated tester of ignition, disconnect a wire from a spark plug and, holding it nippers with reliably zaizolirovanny handles, delay a rubber tip up on a wire and bring the contact plug to well earthed point on the block on distance about 6.4 mm. At an engine provorachivaniye between an electrode and the case the VV tester/plug of a wire and in weight well appreciable spark of bright blue color should slip.

3. If the spark makes the way regularly and its intensity does not cause doubts, repeat check for VV of wires of the remained spark plugs. This check allows to confirm serviceability of a cover and a distributor begunka, without excluding, however, probability of failure actually candles therefore turn out the last and make check of their condition according to given in Head of Control and routine maintenance of the real Management by the description.
4. In the absence of a spark uncover the distributor and check its condition, no less than a condition a begunka (see. Head of Control and routine maintenance). In the presence of moisture traces carefully wipe surfaces of a cover and a begunka pure dry rags, then establish a cover on a place and repeat iskroobrazovaniye quality check;
5. If removal of moisture did not lead to situation correction (the iskroobrazovaniye on former insufficiently intensively or is absent at all), on the V6 models it is necessary to disconnect a secondary wire of the coil from a distributor cover and to connect to it an ignition tester (do not forget to connect wire VV to all candles). Repeat the procedure of check described above.

In the absence of near at hand tester of ignition alternative check of a wire of the coil is made also as well as in a case with VV wires of spark plugs by plug leading to weight on distance about 6.4 mm.

6. In the absence of an iskroobrazovaniye on 4-cylinder models check a condition of a spring and the contact coal button in a distributor cover on existence of traces прогаров and mechanical damages. in case of need replace a distributor cover.
7. If this time there is a normal iskroobrazovaniye, therefore, the cause of failure lies in malfunction of a cover of the distributor, its begunka or the corresponding candle wires (see. Head of Control and routine maintenance).

8. In the absence of an iskroobrazovaniye and at this stage, it is necessary to pass to check of contact connections of primary contour of the coil of ignition, - estimate a condition and reliability of fastening of plugs. Check serviceability of giving of primary tension on the coil from the ignition switch/lock for what measure tension on a positive side of the coil.

In view of that on 4-cylinder models the coil of ignition is built in in the distributor, it is necessary to remove from the last a cover, to disconnect wires from the coil, then to check existence of tension of the battery on the plug of a black and yellow wire. Make necessary corrections, then repeat check.

9. If tension on the coil takes place, and the iskroobrazovaniye still is absent, measure resistance of primary and secondary windings of the coil (see. Section Check of a condition and replacement of the coil of ignition). In case of identification of breaks (the infinite indication of an ohmmeter), replace the coil.
10. If the coil as it should be, serviceability of functioning of the module of management of ignition (ICM) (see. Section Check of serviceability of functioning and replacement of the module of management with ignition (ICM)).
11. It is necessary to charge performance of further checks of PGM-IG system to experts.