Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information
   Check of functioning of system of ignition
   Check of a condition and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management with ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Replacement of a regulator of tension and generator brushes
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and starter installation
   Removal and installation of the traction relay
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Check of installation of a corner of an advancing of ignition

 PERFORMANCE ORDER

Procedure described below is calculated only on check of the base installations made at manufacturer. Possibility of adjustments is not provided, in view of what, the unique purpose of the real check is the assessment of serviceability of functioning of the onboard processor. If during diagnostics of system of ignition (see. The section Check of functioning of system of ignition) to reveal causes of infringement of installations of a corner of an advancing of ignition is not possible, it is necessary to replace RSM for what the car is necessary for driving away on car repair shop.

1. Start the engine and warm up it to normal working temperature.
2. Check and, in case of need, adjust idling turns (see. Head of Control and routine maintenance).

3. At the switched-off ignition find under a cowl a label of VECI and attentively familiarize with the instructions stated in it on installations of a corner of an advancing of ignition. Special value has correctness of installation of turns of idling as frequency of rotation of the engine is directly connected with a corner of an advancing of ignition. Prepare all necessary tools.

   - 1-Vacuum jams - All disconnected vacuum hoses should be corked immediately. For this purpose jams of the various size and a configuration are issued
   - 2-The stroboscope with inductive connection - Provides the pulsation of a bright, ostronapravlenny beam synchronized with the moments of an iskroobrazovaniye on electrodes of a spark plug of the first cylinder. It is connected to VV to a wire of a candle of the first cylinder in compliance by instructions of manufacturers
   - 3-The special wrench - On some models access to a clamping bolt of the distributor is limited and its otdavaniye with application of a key of a usual form becomes the extremely inconvenient

4. At the switched-off ignition, according to instructions of manufacturers connect a stroboscope. A food on a stroboscope usually moves from the onboard storage battery. The reception inductive sensor of a lamp is established on VV a wire of a spark plug of the first cylinder (see. Specifications to Head the Engine).
5. A wire crossing point short-circuit among themselves plugs 8 and 13 of the diagnostic socket (DLC), is will transfer RSM to a mode of base installations of a corner of an advancing of ignition.

6. Find adjusting distributive labels a pulley of a cranked shaft.

7. Start the heated-up engine to normal working temperature and direct a stroboscope beam on the adjusting index.
8. Highlighted by a stroboscope beam a red label on a pulley of a cranked shaft, remaining motionless, it should appear combined with the index.
9. At identification of violations in installations drive away the car on car repair shop for performance of diagnostics of RSM.
10. Muffle the engine and remove a stroboscope.
11. Remove a wire crossing point from plugs of the diagnostic socket.