Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
- Power supply system and release
   Sbrasyvaniye of pressure in a power supply system
   Check of serviceability of functioning of the fuel pump, measurement of pressure of fuel
   Check of a condition and replacement of fuel lines
   Removal and installation of the fuel pump
   Check of a condition and sensor replacement
   Removal and installation of a fuel tank
   Cleaning and repair of a fuel tank - general information
   Removal and installation of assembly of an air purifier
   Removal, installation and adjustment of a cable of an accelerator
   System of electronic injection of fuel (EFI) - the general information
   Check of serviceability of functioning of system of injection
   Removal and installation of the case of a throttle
   Removal and installation of a regulator of pressure of fuel
   Removal and installation of the fuel highway and fuel injectors
   Release system - the general information
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of the fuel highway and fuel injectors

See preventions at the beginning of pressure Sbrasyvaniye's Section in a power supply system.

Removal of the fuel highway from the 4-cylinder engine can be made without preliminary dismantle of the delivery chamber of an air path. On V6 engines the delivery chamber should be removed for the purpose of ensuring access to highways of the left and right ranks of the cylinders, thus both highways can act in film uniform assembly together with the injectors fixed in them.

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for equipment input in action!

2. Dump pressure in a power supply system (see. Undressed Sbrasyvaniye pressure in a power supply system).
3. On the V6 models remove access covers from the top part of the power unit (see. Head Engine).
4. On the V6 models remove the delivery chamber of an air path (see. Head Engine).

5. Disconnect from injection injectors electroconducting.

6. Disconnect from a pressure regulator a hose of return of fuel.

The line of return of fuel is thinner and the hose of a submitting gasoline pipe line (the pressure head line) приболчен to the highway fastens on the regulator union a small collar of spring type, then.

7. Disconnect from the fuel highway of the tire of grounding.
8. Disconnect from the fuel highway the line of supply of fuel.

9. Give fixing nuts/bolts and remove the fuel highway of the engine.

On the V6 models of the highway of both ranks of cylinders should rise at the same time.

10. Take an injector (ы) from the landing nest of the fuel highway.

11. Cнимите also will throw out old sealing and dempferny rings/washers.

It is meaningful to replace all rings/washers used in injectors regardless of their condition.

 

INSTALLATION

 PERFORMANCE ORDER

1. Grease new dempferny washers with pure impellent oil and put on them injection injectors.
2. Establish new sealing rings (also greased with impellent oil), then fill injectors in in the landing nests in the fuel highway.
3. Grease with impellent oil new landing sealing rings and fill them in nests under installation of injectors in the inlet pipeline.
4. Establish assembly of the fuel highway with injectors on the inlet pipeline. Tighten fixing nuts (4-cylinder models) with demanded effort. On the V6 models strongly tighten fixing bolts.
5. Further installation is made as it should be, the return to an order of dismantle of components.
6. Having finished installation, without starting the engine, include ignition for the purpose of activation on pair of seconds of the fuel pump and pressure lifting in a power supply system. Repeat such inclusion two-three times, then check fuel lines, the highway and injectors on existence of signs of leaks.