Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
- Systems of cooling, heating
   Antifreeze - general information
   Check of serviceability of functioning and thermostat replacement
   Check of a condition of fans of system of cooling and chains of their inclusion, replacement of fans
   Removal and installation of a radiator and broad tank of system of cooling
   Check of a condition of the water pump
   Replacement of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of a measuring instrument of temperature of cooling liquid
   Check of serviceability of functioning of the driving electromotor of the fan of a heater and condition of components of its electric chain, replacement of components
   Removal and installation of the electromotor of a drive of the fan of a heater
   Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Check of an electric chain of the coupling of coupling of the To/in compressor
   Removal and receiver dehumidifier installation To/in
   Removal and To/in compressor installation
   Removal and To/in condenser installation
   Removal and To/in evaporator installation with the broad valve
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of the heat exchanger of a heater

Cars considered in the real Management are equipped with system of additional safety of SRS which is better known as a safety cushion. Before performing any works near assembly of a pillow or a steering column, without fail disconnect system in order to avoid receiving traumas as a result of its casual operation (see. Head Onboard electric equipment). Isolation and contact sockets of electroconducting of a chain of SRS are painted in bright yellow color. It is not necessary to connect any diagnostic devices to this chain!

Air central air constantly is under a high pressure. At all do not disconnect refrigerator lines and do not remove any components of system, previously without having executed a discharge of the last. The discharge of central air of air should be made by strengths of the skilled expert in the conditions of a car-care center workshop. At a detachment of refrigerator lines surely put on goggles!

REMOVAL

 PERFORMANCE ORDER

1. Removal of assembly of a heater on considered models is task rather difficult for the average amateur mechanic. Performance demands it from the performer of patience and attentiveness. Electroconductings much of contact sockets and elements of fixture are located under the dashboard in view of what access to them is extremely limited. Usually dismantle of a heater demands preliminary removal of the dashboard and a discharge of a refrigerator path of central air of air. It is necessary to disconnect also driver's and passenger safety cushions and to remove an emphasis of a steering column.
2. If the car is equipped To/in, make a system discharge in the conditions of a specialized workshop. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. Empty cooling system (see. Head of Control and routine maintenance), - cm the prevention at the beginning of the Section Antifreeze - general information.

4. In an impellent compartment disconnect hoses of an okhladitelny path of the engine from inlet and final branch pipes of the heat exchanger of a heater on a back partition of an impellent compartment. For collecting spilled liquid get under branch pipes drain capacity.

Disconnect one of hoses from the heat exchanger and lower it in drain capacity, then submit to a branch pipe of the second hose air of low pressure, - cooling liquid present at the heat exchanger should be forced out from his internal cavities that will essentially reduce risk of hit of liquid on elements of an upholstery of salon in the course of assembly dismantle.

5. Disconnect a driving cable from an operating zaslonka of the heat exchanger of a heater, then give a nut of fastening of assembly of a heater to a partition of an impellent compartment, - the nut is given from an impellent compartment.

Try not to bend and otherwise not to damage the fuel lines laid near a nut and brake tubes.

 

6. Remove the central console, a ware box and the dashboard (see. Head Body).
7. Disconnect from heater assembly contact sockets of electroconducting and a driving cable of management of mixing of air submitted to salon (see. Section Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable)
8. On models without To/in remove the sleeve of an air line laid between assemblies of casings of a heater and its fan. On equipped In models remove also the evaporator (see. The section Removal and To/in evaporator installation with the broad valve).

9. Remove the top clamps of fastening of assembly of a heater to a partition of an impellent compartment from salon. Remove assembly.

10. Release fastening collars to a casing of reception branch pipes of a heating path and take the heat exchanger.

INSTALLATION

 PERFORMANCE ORDER

1. Installation is made upside-down. Do not forget to check serviceability of functioning of managing directors a zaslonok. In case of need make necessary regenerative repair, having replaced the broken or deformed components. Make sure of serviceability of functioning of electric components.
2. Fill system of cooling and remove from it air jams (see. Head of Control and routine maintenance). Connect the battery and start the engine. Check components of system of heating on existence of signs of leaks and serviceability of functioning. At the corresponding complete set make a charging of central air of air in the conditions of a specialized workshop.