Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 Engines
   - General and major maintenance of the engine
      Check of pressure of oil
      Check of kompressionny pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and engine installation
      Alternative versions of schemes of regenerative repair of the engine
      Order of dismantling of the engine by its preparation for major maintenance
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and engine running in after major maintenance
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Trial start and engine running in after major maintenance

 PERFORMANCE ORDER

At primary start of the engine after completion of its regenerative repair near at hand without fail it is necessary to have the class B fire extinguisher!

1. After installation of the power unit on the car, check levels of impellent oil and cooling liquid in it.
2. At the turned-out candles and temporarily disconnected system of ignition (see. The section Check of kompressionny pressure in cylinders), turn the engine, having lifted pressure of oil in it so that there was an operation of the corresponding control lamp on an instrument guard of the car.
3. Screw spark plugs, connect VV of a wire and restore functioning of system of ignition.
4. Start the engine. Start can occur to the small delay necessary for lifting of pressure of fuel, however no special difficulties should arise.

If cottons in the throttle case start to occur, check installation of a corner of an advancing of ignition and gazoraspredeleniye phases.

5. After start it is necessary to warm up the engine to normal working temperature, in the course of a warming up checking it on existence of signs of leakages of oil and cooling liquid. Let's to the engine work within 15 minutes on single turns that is especially important after replacement of shatunny bearings.
6. Muffle the engine, and once again check levels of oil and cooling liquid in it.
7. Now it is possible to start trial runs and an engine running in. Deduce the car to the area where intensity of traffic is minimum and sharply disperse it till speed of 50 ÷ 80 km/h (30 ÷ 50 miles/h). Then dump speed to 50 km/h, having completely closed for this purpose a butterfly valve. Repeat procedure 10 ÷ 12 of times, - arising cyclic loadings will help a usadka of piston rings in relation to walls of cylinders. Again check the engine on leaks.
8. The first 800 km (500 miles) run try to maintain the engine in a sparing mode, regularly and often checking thus level of engine oil. The raised consumption of oil in a running in of the engine is the normal phenomenon.
9. Approximately through 800 ÷ 1 000 km (500 ÷ 600 miles) run replace impellent oil and the oil filter.
10. The following the car can be maintained some hundred kilometers of run in a normal mode.
11. Through 3200 km (2000 miles) again replace impellent oil and the oil filter. Now it is possible to consider the engine rolled finally.