Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 Engines
   - General and major maintenance of the engine
      Check of pressure of oil
      Check of kompressionny pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and engine installation
      Alternative versions of schemes of regenerative repair of the engine
      Order of dismantling of the engine by its preparation for major maintenance
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and engine running in after major maintenance
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft

Condition check

In spite of the fact that bearings of a cranked shaft in the course of major maintenance of the engine are subject to replacement without fail, old loose leaves should be kept for the purpose of attentive studying of their condition which results can give a lot of useful information about the general condition of the engine. On an illustration examples of typical defects of loose leaves of bearings are given.

The exit of bearings out of operation can occur owing to a lack of greasing, hit of particles of dirt, overloads of the engine and corrosion development. Regardless of nature of defects, the reason of damage of loose leaves should be eliminated in the course of performance of major maintenance of the engine in order to avoid recurrence.

For survey take loose leaves of bearings from the beds in the engine block / the bottom heads of rods and radical / шатунных covers and spread out them as installation on a pure working surface. Organization of placement of loose leaves will allow to adhere nature of the revealed defects to a condition of the corresponding necks of a shaft.

Dirt and extraneous particles get to the engine various ways. They can be left in the block in the course of unit assembly, or get via filters or system of ventilation of a case. All particles getting to impellent oil, finally, sooner or later, appear in bearings. Often the metal sawdust which is forming in the course of normal operation of internal components of the engine takes root into a soft material of loose leaves. The probability of presence at bearings of traces of an abrasive is great, in particular, when was not given due consideration to block cleaning after completion of regenerative repair of the engine. Regardless of a way which extraneous particles get to the engine, as a result they with high degree of probability appear introduced in a soft surface of loose leaves of bearings of a cranked shaft and easily come to light at visual survey of the last. Large particles usually are not late in loose leaves, but leave on their surface and a surface of necks of a shaft appreciable traces in the form of scratches, cavities and задиров. The best guarantee from such troubles is the responsible relation to cleaning of components after completion of major maintenance of the engine and care of observance of purity at assembly. Frequent regular change of impellent oil also allows to prolong service life of bearings essentially.

Oil starvation can be a consequence of several various, but often interconnected phenomena. So, the overheat of the engine conducts to a razzhizheniye of engine oil and its replacement from working gaps of bearings. The lack of greasing of bearings can speak in excessive size of working gaps, and also usual leaks (internal or external). Often meeting reason of replacement of oil from gaps of bearings is continuous excess of turns of the engine. Passableness violation маслотоков (usually connected with the wrong combination of openings at installation of components) also conducts to reduction of supply of greasing to bearings. Typical result of oil starvation is the full or local wipe / выщербливание a blanket of loose leaves from a metal substrate. Thus the working temperature can rise to such level that the substrate as a result of an overheat gets a bluish shade.

Essential influence on service life of bearings is rendered also peculiar to the owner of the car by a driving manner. Movement with small speed on an overgear leads to considerable overloads of the bearings, being accompanied replacement of an oil film from their working gaps. Such overloads lead to increase of plasticity of loose leaves and emergence of cracks in a blanket (fatigue deformation). Thus the superficial material starts to crumble and separate from a steel substrate. Car operation in a city cycle (on short distances) conducts frequent trips to development of corrosion of bearings because the insufficient warming up of the engine involves loss of condensate and allocation of chemically aggressive gases. These products accumulate in impellent oil, forming slags and acids. At hit of such oil in bearings aggressive substances promote development of corrosion of loose leaves.

The wrong installation of loose leaves in the course of engine assembly also can be at the bottom of their fast destruction. Too hard landing does not provide the demanded size of a working gap of bearings that leads to their oil starvation. Result of hit under loose leaves (in the course of their installation) extraneous particles is formation of eminences the blanket with which is quickly wiped.

Selection of loose leaves


In case of wear or damage of loose leaves of radical bearings, and also when it is not possible to achieve the correct size of a working gap (see. The section Installation of a cranked shaft and check of working gaps of radical bearings or Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft), a situation can be corrected in the way described below, a way of selection and installation of new loose leaves. If the cranked shaft was exposed to a pro-point, it should be completed with loose leaves corresponding repair (with belittling) the sizes (in this case the procedure given below should not be made). Usually selection of loose leaves is carried out by the experts making a pro-point of necks of a shaft. Regardless of a technique of determination of the demanded size of loose leaves working gaps of bearings should be then are checked with application of a measuring set of Plastigage (see below).

If it is not possible to correct properly size of working gaps by selection of loose leaves, it is necessary to replace a shaft.


Radical bearings

1. In need of selection of new loose leaves of the STANDARD size choose what has the same color marking, as old.

2. If color marking of the old loose leaf is lost, find the marking which has been beaten out on the block around an arrangement of a cover of the corresponding bearing.

3. Also check marking of a class of radical bearings actually on a shaft.

4. At selection of new loose leaves use the corresponding ID card of color marking of bearings.


Shatunnye bearings

1. At selection of new loose leaves of the STANDARD size be guided by color marking of components removed from the car.
2. In case of loss of a color code on old loose leaves, find marking on the bottom heads of rods. The label in the form of figure characterizes a dimensional class of the shatunny bearing (it is not necessary to confuse it to cylinder number).
3. Check also warranty labels actually on a shaft, defining the size of the corresponding shatunny necks (see an accompanying illustration).

ID card of a choice of loose leaves of radical bearings of a cranked shaft for 4-cylinder engines - use the marking put on the block of the engine, and assembly of a cranked shaft, for example: marking С3 means need of installation of loose leaves of yellow and green flowers (where they should be different color), and any of them can be established as in a bearing cover, so in its bed in the block

 


ID card of a choice of loose leaves of radical bearings of a cranked shaft for V6 engines

 

On 4-cylinder engines warranty and digital marking of a class of bearing necks is put on a cheek of the first crank or beaten out in the neighbourhood with each neck separately.

4. At selection of new loose leaves use the corresponding ID card of color marking of bearings.

ID card of a choice of loose leaves of shatunny bearings of a cranked shaft for 4-cylinder engines - use the marking put on cheeks of cranks and the corresponding rods, for example: marking of D4 means need of installation of loose leaves of dark blue color

 


ID card of a choice of loose leaves of shatunny bearings of a cranked shaft for V6-engines use the marking put on cheeks of cranks and the corresponding rods, for example: marking of D4 means need of installation of loose leaves of brown color (pay attention that installation of a combination of loose leaves of two various flowers in certain cases is required)

 


All bearings


Remember that in the final parameter defining correctness of selection of loose leaves, the result of measurement of working gaps in bearings is. With any questions safely address to representatives firm Honda company service centers.