Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 Engines
   - General and major maintenance of the engine
      Check of pressure of oil
      Check of kompressionny pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and engine installation
      Alternative versions of schemes of regenerative repair of the engine
      Order of dismantling of the engine by its preparation for major maintenance
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and engine running in after major maintenance
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Check of a condition of the block of the engine

 PERFORMANCE ORDER

1. Previously the block should be carefully cleared (see. Section Cleaning of the block of the engine).
2. Make external survey of the block about identification of traces of corrosion, cracks and other damages. Check a condition of a carving of boltovy openings. It will be reasonable to make also testing of the block for existence of the hidden cracks in the conditions of a car-care center workshop with use of the special diagnostic equipment. In case of detection of defects the block is subject to regenerative repair or replacement.
3. Check a condition of mirrors of cylinders.

4. Estimate sizes taking place a konusnost and ovality of cylinders:

a) Measure diameter of each of cylinders in top (directly under limit of step wear), the central and bottom sections in the plane of a parallel axis of the cranked;
b) Now measure diameters at the same three levels, but in the plane, a perpendicular axis of the block;
c) The size of a konusnost of the cylinder is defined by a difference between results of measurements in the top and bottom sections. The difference of diameters in a parallel and perpendicular axis of a cranked shaft in each of the planes is called as ovality.
d) Compare results of check to nominal rates (see. Specifications).

5. Operating in the described manner, serially check all cylinders.
6. At detection of appreciable defects or a deviation of results of measurements from standard requirements, the block of cylinders is subject to regenerative machining in the conditions of a car-care center workshop. If in the course of regenerative repair boring of cylinders was made, the engine should be completed with new pistons corresponding repair (with excess) the size.
7. If the condition of mirrors of cylinders during performance of check is found satisfactory at simultaneous observance of standard requirements to a form of cylinders and gaps of landing of pistons in them (see. The section Check of a condition of components of shatunno-piston group), need for a pro-point of cylinders disappears. Will execute only honingovany their mirrors (see enough. Undressed Honingovaniye of mirrors of cylinders).

8. Check planeness of a surface of the block interfaced to a head. Compare result of measurements to requirements of Specifications, in case of need give the block to a pro-point.