Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 Engines
   - General and major maintenance of the engine
      Check of pressure of oil
      Check of kompressionny pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and engine installation
      Alternative versions of schemes of regenerative repair of the engine
      Order of dismantling of the engine by its preparation for major maintenance
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and engine running in after major maintenance
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Cleaning of the block of the engine

 PERFORMANCE ORDER

1. Remove the bridge of covers of radical bearings and take from the beds in covers and the block loose leaves of bearings. Mark loose leaves by means of an adhesive tape on compliance to the beds (bearing No., a block/cover) and put them aside.
2. Scratch out from an interfaced surface of the block all traces of a material of old laying. Try not to leave задиров.
3. Remove from the block all covers and carving caps of oil galleries. Caps are usually tightened very hardly therefore, quite probably, they should be drilled with the subsequent restoration of a carving in an opening. At assembly of the block of a cap it is necessary to replace new.
4. At strong external pollution of the engine it is necessary to deliver it in a car-care center workshop for steam cleaning or heat treatment.
5. After block return from a workshop once again carefully clean all oil openings and galleries - for this purpose special cylindrical brushes of a special form (ask in shops of automobile accessories) are issued. Wash out cavities and channels warm water, - continue washing until from the opposite side of the block pure water will not start to follow. Carefully dry up the block, then slightly grease all pierced surfaces with liquid oil for protection them from corrosion. In the presence of access to a source of the compressed air use it for acceleration of process of drying of the block and a purge of remote cavities and channels.

At work with the compressed air do not forget to put on goggles!

6. At strong pollution or a zashlakovyvaniye of the block it is necessary to resort to shchetochny cleaning by hot water with soap. It is not necessary to try to save time at the expense of the negligent relation to block cleaning. Regardless of the chosen way, track care of pro-cleaning of remote cavities, channels and openings. In summary dry the block and grease the pierced surfaces with liquid oil for protection them from corrosion.

7. Banish all carving openings in the block a tap of the corresponding size for the purpose of a guarantee of compliance of indications of the indicator of a dinamometrichesky key to really developed efforts of a tightening of fixture at engine assembly. Whenever possible, blow then the banished openings the compressed air, having removed from them all small garbage and shaving. Having finished processing of openings, walk a lerka by a carving part of bolts.

8. Establish to the place of a cover of radical bearings, having by hand tightened their fixture.
9. Grease with not stiffening hermetic a carving of new caps and закупорьте them openings of oil galleries. Track durability of a tightening of caps.
10. If are not going to start immediately engine assembly, place the block in a big plastic bag for protection of its pollution.