Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 Engines
   - General and major maintenance of the engine
      Check of pressure of oil
      Check of kompressionny pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and engine installation
      Alternative versions of schemes of regenerative repair of the engine
      Order of dismantling of the engine by its preparation for major maintenance
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and engine running in after major maintenance
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal of shatunno-piston assemblies

 PERFORMANCE ORDER

Before starting extraction from the engine of shatunno-piston assemblies, it is necessary to remove a head (and) cylinders, the pallet of a case and the oil pump with a maslozaborny tube.

1. By means of a special vertical drill completely remove traces of step wear from the top part of cylinders - act according to the instructions of the manufacturer enclosed to a vertical drill. The step is formed on piston stroke border, approximately in 6.4 mm under the top cut of the cylinder at the expense of mechanical production of metal and a nagaroobrazovaniye, to define its existence it is possible to the touch a finger nail. Attempts of extraction of shatunno-piston groups without removal of step development are fraught with damage of pistons.

2. Having finished preparation of cylinders, overturn the engine upside down so that the cranked shaft appeared from above.
3. For the purpose of ensuring access to rods remove a maslootrazhatelny plate.

On 4-cylinder engines of a cover of radical bearings are incorporated the general bridge which then fastens to the block of cylinders. Check axial люфта a shaft on such engines should be made before removal of this bridge (see. Section Removal of a cranked shaft) (and maslootrazhatelny plate). Axial люфт rods on the necks it can be defined through openings in the bridge. For removal of shatunny assemblies the bridge is necessary for dismantling.

4. Before removing rods from a cranked shaft, estimate their size axial люфта on necks of the last. Densely enter an edge (I) measuring щупа into a gap between a lateral wall of the bottom head of a rod and a crank cheek, having completely chosen люфт a rod on a shaft neck. The total thickness of the picked-up edges щупа also will equal to size axial люфта a rod. Compare result of the carried-out measurement to requirements of Specifications. If the size axial люфта exceeds limiting admissible value, this rod is subject to replacement. Axial люфт a new rod, or old on new to a shaft, it can appear less than the bottom admissible limit, in this case the rod can be pierced - consult with specialists of car-care center. Serially check all remained rods.

5. Make sure available on the bottom heads of rods and their covers of identification labels of belonging to the cylinder - do not mix rod number with marking of the size of the shatunny bearing,

in case of need put labels independently by means of a small center punch.

6. In stages (on 1/2 turns for an approach) weaken nuts of fastening of covers of the bottom heads of rods so that there was a possibility of their otvorachivaniye manually. Uncover the first rod together with the loose leaf of the bearing placed in it - try not to drop the last.

On 4-cylinder engines removal of shatunno-piston assemblies can be made only after dismantle of the bridge of covers of radical bearings (see. Section Removal of a cranked shaft).

7. Take from the bottom head of a rod the loose leaf, then, having rested the wooden handle of a hammer against a bearing bed in the bottom head, вытолкните shatunno-piston assembly at the top the cylinder at the top the block. At resistance emergence immediately stop extraction of assembly and check completeness of removal of step wear in the top part of the cylinder.
8. In a similar manner take from the engine the remained shatunno-piston assemblies.

Installation of a rod subject to extraction coaxially to the cylinder is made by the corresponding provorachivaniye of a cranked shaft, - extraction start only after the rod will be strictly located parallel to a cylinder axis!

9. In order to avoid casual mechanical damage of bearings and loss of components, establish into place loose leaves and fix covers of bearings on the bottom heads of the rods, having by hand tightened nuts.
10. Do not remove pistons from rods (for more details see. Section Check of a condition of components of shatunno-piston group).