Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   - V6 engines
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of covers of heads of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft
      VTEC system - the general information
      Removal, check of a condition and installation of assembly of yokes
      Removal, check of a condition and installation of camshafts
      Replacement of maslootrazhatelny caps and klapanny springs with plates
      Removal and installation of heads of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation of a driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit (V6 Engines)
      System of correction of a suspension bracket of the power unit - the general information and check of serviceability of functioning
   + General and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal, check of a condition and installation of assembly of yokes

REMOVAL

 PERFORMANCE ORDER

1. Uncover heads of cylinders (see. Section Removal and installation of covers of heads of cylinders).
2. Bring the piston of the first cylinder into situation VMT (see. The section Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)), remove a gas-distributing belt (see. Section Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM).

3. Weaken on 1/4 turns bolts of fastening of an axis of yokes (for weakening of effort developed by klapanny springs), - act as it should be, the return shown on an illustration.

4. Take axis assembly with yokes from a head of cylinders. Do not turn out fixing bolts finally for the purpose of fixing of components of assembly on an axis.

CHECK

 PERFORMANCE ORDER

1. Having removed assembly of yokes, it will be reasonable to disassemble it for the purpose of more detailed studying of a condition of components. Turn out fixing bolts and remove from yoke and spring axes. It will be reasonable to mark previously the provision of an axis in relation to covers of bearings.

It will be reasonable to fasten yokes of primary and secondary inlet valves rubber bandages. Try to put removed components as their installation as at assembly they should be planted strictly on the former places.

2. Carefully clear components and check them on existence of signs of wear and mechanical damages. Estimate a condition of surfaces of yokes contacting to a camshaft, estimate degree of wear and freedom of rotation of rollers. Check on existence задиров and signs of excessive wear of a surface of landing of yokes on axes, and also walls of landing openings of yokes. Defective components are subject to replacement. Make sure of passableness маслотоков in axes.

3. Take from the landing nests in a head of cylinders proof-readers of klapanny gaps and carefully clean them. Fingers check freedom of a course of plunzher.
4. Check freedom of a course of synchronizing pistons in assemblies of a drive of inlet valves.

INSTALLATION

 PERFORMANCE ORDER

1. Grease all components with pure impellent oil and establish them on the regular places on an axis of yokes.

Pay attention to the marking distinguishing left foreign components from the right-hand.

2. Grease with special greasing for camshafts working surfaces of yokes. Plant the removed components on an axis, then establish assembly on the engine.

3. In strictly certain order in stages (with a small step) tighten bolts of fastening of assembly of yokes with demanded effort.

4. Installation of the remained components is made as it should be, the return to an order of their dismantle.
5. In summary do not forget to make adjustment of klapanny gaps (if in it there is a need) (see. Head of Control and routine maintenance).
6. Start the engine and check it on existence of signs of leakages of oil and serviceability of functioning.