Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   - Four-cylinder engines
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of a cover of a head of cylinders
      VTEC system - the general information and check of a condition of components
      Removal, check of a condition and installation of assembly of yokes
      Replacement of maslootrazhatelny caps and klapanny springs with plates
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal, check of a condition and installation of cogwheels and belt of a drive of balancing shaft
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft
      Removal, check of a condition and camshaft installation
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and flywheel installation / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
      System of correction of a suspension bracket of the power unit - the general information and check of serviceability of functioning
   + V6 Engines
   + General and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and flywheel installation / driving disk

REMOVAL

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove a transmission (see. Head gear shifting Box).
2. On models from RKPP remove coupling assembly (see. Head Coupling and power shafts). At once check a condition of components of coupling and directing bearing.

3. Turn out bolts of fastening of a flywheel / a driving disk to a cranked shaft. If in the course of weakening of bolts the shaft starts to be turned, remove a starter (see. Head engine Electric equipment) also jam a screw-driver between teeths of a wreath of a flywheel (RKPP), or pass a long drift in one of openings of a driving disk, having rested it against a ledge on the block (AT).

4. Remove a flywheel / a driving disk from a cranked shaft.

The weight of assembly of a flywheel / a driving disk is very considerable, - it will be reasonable to resort to the help of the assistant. Put on working gloves not to cut a hand about keen edges of teeths of a wreath of assembly.

5. Carefully wipe a flywheel the rags moistened in acetone, having completely removed from it oil and greasing traces. Check a working surface of a flywheel on existence of cracks, the furrows left heads of rivets of a frictional disk of coupling, traces of an overheat and задиров. Minor defects can be eliminated by means of a fine-grained emery paper. Check a gear wreath on existence of cracks and chips of teeths. Lay a flywheel on a flat surface for the purpose of an assessment of its planeness (use a planeness measuring instrument). In case of need give assembly to a pro-point.
6. Wipe interfaced surfaces of a flywheel / a driving disk and a cranked shaft. If signs of leakages of oil through a back epiploon of a cranked shaft take place, make its replacement (see. Section Replacement of a back epiploon of a cranked shaft).

INSTALLATION

 PERFORMANCE ORDER

1. Establish a flywheel / a driving disk on a cranked shaft.

On some engines the directing pin is provided, or fixing openings are located asymmetrically that guarantees unambiguity of landing of assembly. Before rolling fixing bolts, grease their carving part with fixing hermetic.

2. Having blocked a flywheel / a driving disk from a provorachivaniye (see paragraph 3), tighten fixing bolts with demanded effort in a diagonal order.
3. Further installation is made as it should be, the return to an order of dismantle of components.