Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   - Four-cylinder engines
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of a cover of a head of cylinders
      VTEC system - the general information and check of a condition of components
      Removal, check of a condition and installation of assembly of yokes
      Replacement of maslootrazhatelny caps and klapanny springs with plates
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal, check of a condition and installation of cogwheels and belt of a drive of balancing shaft
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft
      Removal, check of a condition and camshaft installation
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and flywheel installation / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
      System of correction of a suspension bracket of the power unit - the general information and check of serviceability of functioning
   + V6 Engines
   + General and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal, check of a condition and installation of the oil pump

REMOVAL

 PERFORMANCE ORDER

1. Remove a gas-distributing belt and a belt of a drive of balancing shaft (see. Sections Removal, check of a condition and installation of cogwheels and belt of a drive of balancing shaft and Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM). Remove a cogwheel of a forward balancing shaft and assembly of a casing of a gear wheel of a back balancing shaft. Disconnect from the main plait electroconducting of sensor SKR/VMT. Turn out four fixing bolts and remove the sensor from the case of the oil pump.
2. Remove the pallet of a case of the engine (see. Section Removal and installation of the pallet of a case of the engine).

3. Disconnect assembly of a maslozabornik with the mesh filter and a tube from the bridge of covers of radical bearings and the pump case.

4. Turn out fixing bolts and remove from the engine the oil pump.

5. Turn out fixing screws and remove from the pump a cover.

Not to break a shlitsa in heads of fixing screws their easing it is better to make by means of a shock screw-driver.

CHECK

 PERFORMANCE ORDER

1. Measure size of working gaps of gear wheels of the pump. Compare results of measurements to requirements of Specifications. If the size of gaps falls outside the limits admissible values, replace the pump.

2. Turn out a stopper of the reduktsionny valve and take from a nest in the pump case klapanny a spring and a plunzher. Check a spring on existence of deformations, and a plunzher - on existence of scratches and задиров. Defective components are subject to replacement.
3. Establish gear wheels in the case of the pump and fill cavities between their teeths technical vaseline (as initial filling at primary start).
4. Grease screws of fastening of a cover of the pump with anti-taking hermetic. Establish a cover, screw screws and tighten them with demanded effort. Establish in the pump case a spring and a plunzher of the reduktsionny valve. Having replaced a sealing washer, screw a stopper and strongly tighten it.

INSTALLATION

 PERFORMANCE ORDER

1. Slightly grease with RTV hermetic a surface of the case of the pump interfaced to the block. Make sure available on the place of a directing pin and establish the pump, previously having replaced sealing rings. Grease with RTV hermetic a carving of fixing bolts, screw them and tighten with demanded effort.

Installation of the pump should be made within 5 minutes after hermetic imposing. Track, that лыски in an internal gear wheel of the pump were combined with reciprocal лысками on a pin of a cranked shaft.

2. Establish on a back balancing shaft cogwheel assembly with a gear wheel casing. Afterwards establish a gas-distributing belt and a belt of a drive of balancing shaft.
3. Establish into place sensor SKR/VMT, having tightened bolts of fastening it to the pump with demanded effort. Restore initial connection of electroconducting.
4. Establish into place assembly of a maslozabornik, having tightened fixing bolts with demanded effort (do not forget to replace sealing laying).
5. Establish the case pallet (see. Section Removal and installation of the pallet of a case of the engine).
6. Further installation is made as it should be, the return to a dismantle order. In summary do not forget to fill in in the engine engine oil and to fill cooling system (see. Head of Control and routine maintenance).
7. Start the engine and check its existence of signs of leaks.