Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
- Engine
   - Four-cylinder engines
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of a cover of a head of cylinders
      VTEC system - the general information and check of a condition of components
      Removal, check of a condition and installation of assembly of yokes
      Replacement of maslootrazhatelny caps and klapanny springs with plates
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal, check of a condition and installation of cogwheels and belt of a drive of balancing shaft
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft
      Removal, check of a condition and camshaft installation
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and flywheel installation / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
      System of correction of a suspension bracket of the power unit - the general information and check of serviceability of functioning
   + V6 Engines
   + General and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of the pallet of a case of the engine

REMOVAL

 PERFORMANCE ORDER

1. Warm up the engine to normal working temperature, then merge from it engine oil and remove the oil filter (see. Head of Control and routine maintenance).
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. To Poddomkratta the car also establish it on props. Remove protection of a case.

4. Turn out bolts of fastening of an edge of rigidity of the engine.

5. Give bolts of fastening of the pallet to the engine block.

6. Обстучав the pallet on perimeter a hammer with soft brisk for the purpose of destruction of a layer of hermetic, separate it from the block, - at all do not make attempts to hook the pallet under an interfaced surface!

INSTALLATION

 PERFORMANCE ORDER

1. Scratch out from interfaced surfaces of the pallet and the block all traces of hermetic and a material of old laying. Remove from the pallet or the block face sealing inserts. Carefully wipe interfaced surfaces the rags moistened in acetone. Clean and dry carving openings in the block.
2. Wash out the pallet solvent and carefully dry it. Make sure of absence of deformations of an adjusting flange of the pallet, in case of need lay the pallet a flange on the flat wooden block and make a rikhtovka.
3. Impose hermetic on surfaces of interface of the oil pump with the block and the holder of a back epiploon of a cranked shaft with the block. Also grease with hermetic a back part of laying of the pallet on corners of a semicircular face sealing insert.
4. Accurately press the pallet to the block.
5. Screw two lobbies, two back and two central nuts and by hand tighten them. Screw the remained bolts and in stages (with a small step) tighten fixture with demanded effort. Begin a fixture tightening in the direction from the center to edges of the pallet, moving on a spiral. Remember that pulling of fixture is fraught with development of leaks.
6. Establish into place an edge of rigidity of the engine and fix it bolts, having tightened them with demanded effort (see. Specifications to Head a gear shifting Box).
7. Fill in engine oil (see. Head of Control and routine maintenance), start the engine and check the pallet on existence of leaks.