Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
- Gear shifting box
   + 5-step manual box of gear shifting (RKPP)
   - 4-step automatic transmission (AT)
      Problem diagnostics AT/CVT - the general information
      Removal, installation and adjustment of a cable of gear shifting
      Removal and installation of the lever of switching (selector) of transfers
      Blocking system - the general information, condition check, replacement and adjustment of an electromagnet of management
      Adjustment and replacement of the sensor switch of provision of transmission
      Check and replacement of electromagnetic valves of management with transmission functioning
      Removal and installation of 4-step and automatic transmission (AT)
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal, installation and adjustment of a cable of gear shifting

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.

REMOVAL

 PERFORMANCE ORDER

1. Remove the central console (see. Head Body).

2. Give a lock-nut of a regulator of a cable.
3. Develop the rubber plug through passage on 1/4 turns counter-clockwise and together with a cable liberate it from a basic arm.

4. To Poddomkratta the car also establish it on props.
5. Under the car remove an exhaust pipe with the thermofilter (see. Head of the Power supply system and release).

6. Under the car, around placement of the console remove directing arm of a cable and liberate from the bottom panel the rubber plug of the last through passage.

7. Turn out bolts from the holder of a cable of management of gear shifting.

In order to avoid damage of knot of connection of a cable to a control lever, the holder it is necessary to remove before covers.

8. Turn out fixing bolts and uncover a cable of management of switching.

9. Turn out a lock bolt and take a control lever with the cable of switching connected to it from transmission assembly.

INSTALLATION

 PERFORMANCE ORDER

1. Under the car pass assembly of a new cable in an opening of access and establish into place directing arm.
2. Transfer the lever of switching (selector) to the situation "R".
3. On transmission connect a control lever with the cable of switching attached to it to an operating rod.
4. Screw a new lock bolt of fastening of the lever and fix it, having bent a tag of a lock washer.
5. Establish on a cover the holder of a cable of management of switching, then establish cover assembly on transmission.
6. In salon of the car develop the plug through passage on 1/4 turns clockwise and plant assembly on a basic arm.
7. Include ignition (do not start the engine) and make sure that the indicator of inclusion of a reverse gear burns.
8. If the cable is established incorrectly, push it forward against the stop, then extend back on one click, having transferred to the situation corresponding to inclusion of a reverse gear.

9. Put on a cable tip a bolt of the lever of switching, having tracked correctness of combination of a groove with rectangular ledges of a bolt.

10. Serially translate the switching lever through all provisions and make sure of serviceability of switching of transmission.
11. Further installation is made as it should be, the return to an order of dismantle of the corresponding components. In case of need make adjustment of a cable of switching

ADJUSTMENT

 PERFORMANCE ORDER

1. Start the engine, transfer the selector lever to the situation "R" and make sure of serviceability of inclusion of a reverse gear. If transfer does not join, it is necessary to make cable adjustment. Muffle the engine.
2. Remove the central console (see. Head Body).

3. Transfer the selector lever to the situation "N", then release a lock-nut of a regulator of a cable.

4. Push a cable forward against the stop, then release it, - transmission should be switched in the situation "R". pull a cable back on one click so that it was fixed in the new situation corresponding to the situation "R".
5. Pass a core in diameter of 6.1 mm in a special opening in an assembly bracket of the basis of the lever of switching, - the opening is located from the driver's party of a casing of the lever. After the core will be passed in an opening in an assembly bracket of the basis of the lever, level the last and pass a core in an opening in its basis. Now assembly will appear fixed.

6. Put on a cable tip a lever bolt.

7. Screw a lock-nut and fix a cable in this situation.
8. Take a core fixing assembly.
9. Start the engine and make sure of serviceability of functioning of assembly of management of gear shifting.