Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Search of causes of failures of electric equipment
   Safety locks - the general information
   Chain breakers
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Check of serviceability of functioning and replacement of podrulevy switches
   Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column
   Check of serviceability of functioning and replacement of switches of the dashboard
   Check of serviceability of functioning of measuring instruments of a combination of devices
   Removal and installation of a combination of devices
   Removal and installation of a radio receiver and loudspeakers
   Removal and installation of the aerial of a radio receiver
   Replacement of lamps of head headlights
   Adjustment of the direction of optical axes of head headlights
   Replacement of block headlights
   Replacement of lamps
   Running fires of light time of day (DRL)
   Check of serviceability of functioning and replacement of the electromotor of a drive of screen wipers
   Check of serviceability of functioning and replacement of horns of a horn
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   Control system of speed (темпостат) - general information and check of serviceability of functioning
   The electric drive of window regulators - general information and check of serviceability of functioning
   The uniform lock - general information and check of serviceability of functioning
   The electric drive of external rear-view mirrors - general information and check of serviceability of functioning
   Safety cushions - the general information
+ electric equipment Schemes





Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. The Safety cushion section - the general information). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.


Remove casings of a steering column and a knee emphasis (see. Head Body).

CHECK

 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the bottom section of the dashboard from the driver's party of the car (see. Head Body). Moving on an electroconducting plait from the ignition switch down along a steering column to the left assembly block, disunite the electric socket.
3. Check the socket on conductivity existence between contact plugs in each of positions of the ignition key.

 

4. At identification of violations in distribution of conductivity replace the switch.
5. Make sure of density of landing of the cylinder of the lock in all provisions of a key and correctness of placement of marking. The worn-out lock will divide to replacement.

REPLACEMENT

Ignition switch

 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the top and bottom sections of a casing of a steering column (see. Head Body).
3. Insert a key into the lock and turn it in the situation LOCK (Blocking).

4. Turn out two fixing screws and remove switch assembly from a steering column.

Lock cylinder

 PERFORMANCE ORDER

1. Remove top and covers of a casing of a steering column and the bottom section of furnish of the dashboard (see. Head Body).
2. Give fixing nuts and lower a column. At the corresponding complete set of the car disunite sockets of electroconducting of assembly of an immobilization of start.

3. Assembly of the lock is fixed in a column by two bolts with srezny heads which are necessary for drilling (use a drill on 4.8 mm).

4. Release a collar and remove the cylinder of zamkovy assembly from a steering column. At the corresponding complete set of the car remove from the old cylinder the block of an immobilization of start. Rearrange an immobilizator on the new cylinder.

At replacement for any reason of the device of an immobilization of start it is necessary to reprogram the module of management (RSM) in the conditions of car repair shop.

5. Get the replaceable cylinder on a regular place (without a key) and strongly tighten new fixing bolts.
6. Insert a key into the cylinder and make sure of serviceability of functioning of assembly.
7. Tighten fixing bolts before cutting of their heads. At the corresponding complete set of the car connect electroconducting to the device of an immobilization of start.
8. Further assembly is made as it should be, the return to an order of dismantle of the corresponding components.
9. In summary connect the battery (at first a positive wire, then negative).