Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle/cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of the main section of the dashboard

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove finishing sections of the dashboard (see. The section Removal and installation of finishing sections of the dashboard) and assembly of the central console (see. Section Removal and installation of the central console).
3. Remove a combination of devices (see. Head Onboard electric equipment) and a ware box (see. Section Removal and installation of finishing sections of the dashboard).
4. At the corresponding complete set of the car disconnect electroconducting and remove a passenger safety cushion (see. Head Onboard electric equipment).
5. Remove from the central part of the dashboard radio tape recorder assembly (see. Head Onboard electric equipment).

6. Remove a knee emphasis with a rigidity edge (see. The section Removal and installation of finishing sections of the dashboard), then turn out bolts of fastening of a steering column and lower it down, having provided possibility of free removal of the main section of the dashboard.

7. Take a coin box from the lower part of the deflector of a driver's ventilating air line and give two fixing screws located under it. Release the top and central clamps and remove the deflector, disconnecting electroconducting of a drive of the top hatch and темпостата (at the corresponding complete set).

8. Having hooked a screw-driver, remove the deflector of a passenger ventilating air line.

In order to avoid damage of a surface of the dashboard, paste over a lattice on perimeter with an adhesive tape.

9. At dismantle of the main section of the dashboard it is necessary to disunite a set of electric sockets. It will be reasonable to mark them previously.

10. Turn out all bolts of fastening of the main part of the dashboard to a car body. Lift the panel (besides bolts it fastens in the middle three plastic pins) and, having separated it from the wind flew down, take from car salon through a driver's door.

11. Installation is made upside-down.