Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle/cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of panels of an internal upholstery of doors

For protection of hands against cuts at performance of procedures through access openings in a doorframe put on gloves.

REMOVAL

 PERFORMANCE ORDER

1. On models with a manual drive of window regulators remove the lowering handle / поднимания flew down.

2. Remove the button of switching off of the lock of a door.
3. For dismantle of the internal handle of a door remove a plastic protective cap and turn out the unique fixing screw. Liberate handle assembly from the door panel and disconnect from it an executive rod. At the corresponding complete set of the car disconnect electroconducting of the activator of the lock.

4. Remove a decorative cover of external basic knot of a rear-view mirror.

5. Turn out screws of fastening of the panel of an internal upholstery, and also the screw of fastening of assembly of an armrest, then accurately delay the panel on itself, releasing fixing clamps. Moving on panel perimeter, serially release all clamps.

Clamps are located rather deeply under edge of the panel to use the standard tool for a poddevaniye of the last.

6. After all clamps will be released, disunite all remained electric sockets and remove the panel from a doorframe.

7. For the purpose of ensuring access to located in a doorframe to the external handle and a window regulator regulator, remove assembly of management by the electric drive (at the corresponding complete set of the car), assembly door a bracket of the panel and loudspeaker assembly (see. Head Onboard electric equipment), then accurately separate the plastic vlagozashchitny screen.

INSTALLATION

 PERFORMANCE ORDER

1. Before installation of the panel of an internal upholstery make sure available on the places and serviceability of a condition of all its clamps.
2. At the corresponding complete set of the car connect electroconducting to the activator of the door lock and the control panel the window regulator electric drive. Establish the panel on a door. Reliably latch all provided clamps. Establish on a place and fix the screw assembly of the internal handle. Establish the lock switch (if it is provided) / a ware pocket (strongly tighten the fixing screw). Establish the handle of a manual drive window regulator/assembly of management by electric drive functioning.