Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a pushing bar of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of a rotary fist

REMOVAL

 PERFORMANCE ORDER

If the cap of a disk is not fixed by wheel nuts, begin with performance of procedure of paragraph 4.

1. Weaken nuts of fastening of a wheel, поддомкратьте a front of the car and establish it on props.
2. Give wheel nuts and remove a decorative cap from a disk, remove a wheel.
3. A drift расчеканьте a washer of a stupichny nut, then establish into place a wheel without a cap and lower the car on the earth.

4. By means of a face natural a long collar weaken a stupichny nut.

5. Weaken wheel nuts, поддомкратьте a front of the car and establish it on props. Remove a wheel and give a stupichny nut.
6. Liberate a flexible brake hose from an arm on assembly of a rotary fist. To Otboltita a support of the brake mechanism also tie up it a wire to a screw spring. Remove also anchor bracket of a support and a brake disk (see. Head Brake system).
7. Turn out two fixing screws and remove a brake disk from stupichny assembly (see. Head Brake system).
8. Remove the wheel ABS sensor (see. Head Brake system).
9. Disconnect from a rotary fist a tip of steering draft (see. Section Removal and installation of tips of steering drafts).
10. Separate the bottom lever of a suspension bracket from a spherical support in the lower part of a rotary fist (see. Section Removal and installation of the bottom control lever of a forward suspension bracket).
11. Separate the top end of a fist from a spherical support of the top lever of a suspension bracket (see. Section Removal and installation of the top control lever of a forward suspension bracket).

12. Accurately delay fist assembly with a nave outside, having removed it from a pin of a power shaft. In case of need knock on a pin end face with a hammer with soft brisk for the purpose of CV JOINT liberation from a nave. Tie up assembly of a power shaft by a wire in order to avoid damage of the internal CV JOINT.

13. If there is a need for replacement of the stupichny bearing, deliver assembly of a rotary fist in a car-care center workshop.

INSTALLATION

 PERFORMANCE ORDER

1. If made assembly dismantle, establish a nave on a rotary fist (work should be made in the conditions of a car-care center workshop).
2. Slightly grease with special greasing of a shlitsa of an external pin of a power shaft. Pass a pin through an opening in a nave, at the same time filling on a regular place a rotary fist.
3. Connect the top part of a fist to a spherical support of the top lever of a suspension bracket (see. Section Removal and installation of the top control lever of a forward suspension bracket). Tighten a nut of a spherical finger with demanded effort and fix its new the shplinty.

Tighten a nut with the minimum admissible effort, then, hold on it before combination of openings under landing шплинта.

4. Connect a spherical support in the lower part of a fist to the bottom lever of a suspension bracket (see. Section Removal and installation of the bottom control lever of a forward suspension bracket). Tighten with demanded effort a koronchaty nut and fix its new shplinty (see. The remark in the previous paragraph).
5. Establish to the place of a brake disk, having strongly tightened fixing screws.
6. Establish an anchor bracket and a support, having tightened fixture of components with demanded effort (see. Head Brake system). Fix a flexible brake hose in a basic arm on assembly of a rotary fist. Strongly tighten fixing bolts.
7. Screw on a pin of a power shaft a stupichny nut and strongly tighten it.
8. Establish a wheel (if it is necessary - a disk cap), lower the car on the earth and tighten wheel nuts with demanded effort (see. Specifications to Head of Control and routine maintenance).
9. Tighten a stupichny nut with demanded effort (see. Specifications to Head Coupling and power shafts).