Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a pushing bar of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Corners of installation of wheels

 

Corners of installation of forward wheels define geometry of provision of the last concerning a car and paving suspension bracket. Violation of adjustment of this geometry conducts to decrease in controllability of the car and increase of speed of wear of tires. Into number of subjects to control of corners of installation of forward wheels of the car enter disorder, выбег (a corner of a longitudinal inclination of an axis of turn of a wheel) and convergence. One of parameters - convergence, and, both forward, and back wheels of the car is subject to adjustment only. Sizes of disorder and выбега forward wheels should be checked on a regular basis for an assessment of degree of wear of components of a suspension bracket and a steering drive.

Adjustment of corners of installation of wheels is among demanding special accuracy of measurement of procedures for which high-quality performance existence of special, rather bulky and expensive equipment is necessary. It will be most correct to charge performance of this work to professional mechanics of car-care center. Below, for the general understanding, definitions of each of under control corners of installation of wheels of the car which knowledge will facilitate communication of the owner of the car with the car-care center personnel are given.

The data size to each other forward edges of wheels of the car is called as convergence. Such violation of parallelism of installation of wheels allows to minimize wear of a protector for the account юза at commission of turns. At zero convergence distance between forward edges of wheels equally to distance between their back edges. Normal convergence usually does not exceed inch shares (1 inch = 2.54 cm). Adjustment of convergence of forward wheels is carried out by adjustment of length of steering drafts at the expense of change of provision of their tips. For correction of convergence of back wheels the special adjusting kulachkovy bolt screwed in the internal end of a control lever of a back suspension bracket is provided. Violation of adjustment of convergence conducts to acceleration of wear of protectors of tires at the expense of a proskalzyvaniye them on a paving.

The tilt angle of the plane of wheels concerning a vertical is called as disorder. If wheels are inclined by the upper edges outside, disorder is called as positive, and on the contrary. The size of disorder is measured in degrees. Correctness of adjustment of disorder defines size and the provision of a spot of contact of protectors with the road and allows to compensate changes in suspension bracket geometry during commission of turns and at car movement on a rough paving. On considered models of cars possibility of adjustment of disorder is not provided.

Vybegom is called a deviation corner from a vertical of an axis of turn of a wheel in the plane of the last. If the axis of turn is inclined back, выбег is called as positive, on the contrary. Adjustment выбега forward wheels is carried out by selection of the remote washers enclosed under pushing bars of a suspension bracket.