Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a pushing bar of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of reechny transfer

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation. In order to avoid SRS system damage, Track, that the steering shaft was not turned after removal of a steering wheel. Block a column the ignition key at the rectilinear provision of forward wheels.

REMOVAL

 PERFORMANCE ORDER

1. Park the car with the forward wheels developed in rectilinear situation. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! Under the dashboard uncover the connecting hinge of a steering column.

2. Mark the provision of an intermediate shaft of a steering column in relation to an entrance shaft of reechny transfer, then release the coupling screw.

3. Cock the parking brake. Weaken wheel nuts. To Poddomkratta a car front also establish it on props. Remove wheels.

4. Merge hydraulic liquid of PAS system in the prepared capacity: disconnect from a case of reechny transfer submitting and returnable hydraulic lines.

Do not release shtutserny connections of the lines going to the pressure head cylinder of the steering mechanism.

5. For the purpose of minimization of losses of liquid закупорьте the open ends of lines.
6. Liberate tips of steering drafts from levers of rotary fists (see. Section Removal and installation of tips of steering drafts).
7. Disunite the socket of electroconducting of a l-probe (see. Head Engine management) also remove the catalytic converter.
8. Disconnect a cable (ы) a gear shifting drive (see. Head gear shifting Box).

9. Remove from the chassis and a case of reechny transfer intensifying plates.

10. Prop up the steering mechanism from below and give bolts of its fastening). Omit assembly of reechny transfer, accurately deducing an intermediate shaft of a steering column from gearing with entrance shaft of the mechanism. Not to hook on a back beam, slightly incline assembly of the steering mechanism, and take it from under the car.

INSTALLATION

 PERFORMANCE ORDER

1. Get assembly of the steering mechanism on the regular place and enter its entrance shaft into gearing with intermediate shaft of a steering column (track correctness of combination of the landing labels put in the course of dismantle).
2. Screw bolts of fastening of assembly of reechny transfer (do not forget to enclose under heads of bolts of a washer) and tighten them with demanded effort.
3. Establish strengthening plates, tighten bolts of their fastening with demanded effort.
4. Connect tips of steering bent for to a rotary fist (see. Section Removal and installation of a steering wheel).
5. Screw a coupling bolt of an intermediate shaft and tighten it with demanded effort.
6. Establish into place a cover of access to the connecting hinge. Track, that both clamps got to reciprocal openings in floor panels.
7. Connect to a case of the steering mechanism the hydraulic PAS lines. Fill in in the PAS tank necessary amount of more freshly hydraulic liquid of a demanded grade (see. Head of Control and routine maintenance).
8. Establish wheels. Lower the car on the earth and tighten wheel nuts with demanded effort (see. Specifications to Head of Control and routine maintenance).
9. Pump over system of hydrostrengthening of a wheel (see. The section air Removal from a hydraulic path of system of strengthening of a wheel).