Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a pushing bar of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of a steering wheel

Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation. In order to avoid SRS system damage, Track, that the steering shaft was not turned after removal of a steering wheel. Block a column the ignition key at the rectilinear provision of forward wheels.

REMOVAL

 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove from assembly of a steering wheel an access cover.

3. For the purpose of an immobilization of a safety cushion disunite the 2-contact socket of electroconducting of its module.

4. Remove covers of access to bolts of fastening of the module of a safety cushion from both parties of the lower part of a steering wheel, turn out bolts with heads of the TORX type with which the module fastens to wheel assembly.

5. Accurately take the module of a safety cushion and transfer it to a safe place.

Try not to turn the module the face to itself. At all do not stack from above on the module any extraneous subjects.

6. Disunite electric sockets of the button of a horn and (at the corresponding complete set) темпостата.

7. Turn out a bolt of fastening of a steering wheel and mark the provision of a nave of the last concerning a column shaft.

8. Having pulled a wheel it is strict parallel to the axis, remove it from a steering shaft. If the wheel does not give in, a little пораскачивайте it.

At all do not roll stripper bolts in assembly of a steering wheel more than on five turns as it can lead to failure of the cable SRS reel. For the same reasons do not allow rotation of a shaft of a column at the removed steering wheel!

INSTALLATION

 PERFORMANCE ORDER

1. Make sure that forward wheels of the car are developed in rectilinear situation.

2. Make sure of correctness of centering of the cable SRS reel, - the arrow with marking of TORAHS should indicate strictly up. If the column shaft after removal of a steering wheel did not rotate with this question there should be no problems. If for any reason the shaft nevertheless turned, make centering, operating as follows:

a) Turn a cable drum against the stop clockwise;
b) Turn a cable drum counter-clockwise approximately on two and a half turns so that the label specified strictly up.

3. Get a steering wheel in regular situation and achieve combination of the landing labels put in the course of dismantle. Make sure that directing pins of a column get to reciprocal openings from a reverse side of a steering wheel, and the nave correctly entered into gearing with the returnable device of the switch of indexes of turns. Plant a wheel nave on a pin of a steering shaft, screw a fixing bolt and tighten it with demanded effort.

4. Connect sockets of a horn and (at the corresponding complete set) темпостата.

5. Establish into place the SRS module, having fixed it new TORX bolts. Track, that bolts were tightened with demanded effort. Establish to the place of a cover of access to screws.
6. Connect together halves of the socket of the cable SRS reel.
7. Establish an access cover on assembly of a steering wheel.