Honda Accord

1998-1999 of release

Repair and car operation



Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a pushing bar of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes





Removal and installation of stupichny assembly of a back wheel

REMOVAL

 PERFORMANCE ORDER

1. Weaken nuts of fastening of the corresponding back wheel. To Poddomkratta a car back also establish it on props. Remove a wheel.

Models with disk brake mechanisms of back wheels

2. To Otboltita from stupichny assembly an arm of fastening of a brake hose. To Otboltita a support also tie up it a wire to a screw spring. Remove an anchor bracket of a support (see. Head Brake system).
3. Turn out two fixing screws and remove a brake disk from stupichny assembly (see. Head Brake system).

Models with drum-type brake mechanisms of back wheels

4. Disconnect the brake line from the wheel cylinder (see. Head Brake system).
5. Remove a drum and assembly of brake boots (see. Head Brake system).

All models

6. Remove from stupichny assembly a nave with the wheel bearing (see. The section Removal and installation of assembly of a back nave with the wheel bearing).
7. Give a nut of fastening of the top end of the corresponding rack of the stabilizer of cross-section stability (see. Section Removal and installation of a bar of the back stabilizer of cross-section stability).
8. Disconnect from stupichny assembly the bottom end of the shock-absorber (see. The section Removal and installation of assembly of the back shock-absorber with a screw spring).
9. To Otboltita from stupichny assembly suspension bracket levers (see. Section Removal and installation of levers of a back suspension bracket).
10. Remove stupichny assembly from levers.
11. In case of need replacements of the wheel bearing remove from assembly a nave (see. The section Removal and installation of assembly of a back nave with the wheel bearing).

INSTALLATION

 PERFORMANCE ORDER

1. Connect to stupichny assembly suspension bracket levers (see. Section Removal and installation of levers of a back suspension bracket). Tighten fixing nuts with demanded effort.
2. Connect to assembly the bottom end of the shock-absorber. With demanded effort tighten a nut of a fixing bolt.
3. Connect to the arm on stupichny assembly a rack of the stabilizer of cross-section stability. Tighten with demanded effort a fixing nut.
4. Establish on the regular place nave assembly with the wheel bearing (see. The section Removal and installation of assembly of a back nave with the wheel bearing).
5. Establish components of the brake mechanism (see. Head Brake system). At work on model with disk brake mechanisms of back wheels do not forget to pump over brake system.
6. Establish into place a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see. Specifications to Head of Control and routine maintenance).